This page is part of archived documentation for openHAB 2.5. Go to the current stable version

# Caddx Binding

The Caddx binding is used for communicating with the Caddx alarm panels. Also known as Interlogix.

It provides connectivity to the NetworX alarm panels via a RS-232 serial connection to the NX-584E interface or directly to the NX-8E.

# Supported Things

This binding supports the following Thing types

Thing	Thing Type	Description
bridge	Bridge	The RS-232 interface.
panel	Thing	The basic representation of the alarm System.
partition	Thing	Represents a controllable area within the alarm system.
zone	Thing	Represents a physical device such as a door, window, or motion sensor.
keypad	Thing	Represents a keypad. (Not yet functional)

# Discovery

First the bridge must be manually defined. The serial port, baud rate and protocol have to be set correctly to match the respective configuration of the panel (see below Prerequisites section). After the bridge is manually added and available to openHAB, the binding will automatically start to discover partitions and zones and add them to the discovery inbox.

Note: There is currently no support to discover the available keypads.

# Prerequisites

For the binding to work the panel has also to be programmed appropriately.

# Programming locations for the NX-8E control panel

Location	Segment	Value	Description
207	1	1	Serial Port selector
208	1	0 - 4	Baud rate table 0 = 2400 Baud 1 = 4800 Baud 2 = 9600 Baud 3 = 19200 Baud 4 = 38400 Baud
209	1	Off/On	Home automation protocol 1 = Off: Binary. On: ASCII.
210	1	2,5,6,7,8	Enabling the Transitions
210	2	1,2,3,4
211	1	2,4,5,6,7,8	Programming the Command/Request enables
211	2	1,2,3,4,5	(Flags 4 and 5 are not yet functional. Can be ignored.)
211	3
211	4	5,7,8
212	1	192	Programming the LCD keypad address. (Not yet functional. Can be ignored.)

# Programming locations for the NX-584E home automation module

Location	Segment	Value	Description
0	1	Off/On	Home automation protocol 1 = Off: Binary. On: ASCII.
1	1	0 - 4	Baud rate table 0 = 600 Baud 1 = 1200 Baud 2 = 2400 Baud 3 = 4800 Baud 4 = 9600 Baud 5 = 19200 Baud 6 = 38400 Baud 7 = 76800 Baud
2	1	2,5,6,7,8	Enabling the Transitions
2	2	1,2,3,4
3	1	2,4,5,6,7,8	Programming the Command/Request enables
3	2	1,2,3,4,5	(Flags 4 and 5 are not yet functional. Can be ignored.)
3	3
3	4	5,7,8
4	1	192	Programming the LCD keypad address. (Not yet functional. Can be ignored.)

# Thing Configuration

The things can be configured either through the online configuration utility via discovery, or manually through the configuration file. The following table shows the available configuration parameters for each thing.

Thing	Configuration Parameters
bridge	`serialPort` - Serial port for the bridge - Required
	`protocol` - Protocol used for the communication (Binary, Ascii) - Required - Default = Binary
	`baud` - Baud rate of the bridge - Required - Default = 9600
	`maxZoneNumber` - Maximum zone number to be added during discovery - Required - Default = 16
partition	`partitionNumber` - Partition number (1-8) - Required
zone	`zoneNumber` - Zone number (1-192) - Required
keypad	`keypadAddress` - Keypad address (192-255) - Required

A full example is further below.

# Channels

Caddx Alarm things support a variety of channels as seen below in the following table:

Channel	Item Type	Type	Description
send_Command	String	Command	Send a command to the panel
panel_firmware_version	String	Configuration	Firmware version
panel_log_message_n_0	String	Runtime	Log message 10
panel_log_message_n_1	String	Runtime	Log message 9
panel_log_message_n_2	String	Runtime	Log message 8
panel_log_message_n_3	String	Runtime	Log message 7
panel_log_message_n_4	String	Runtime	Log message 6
panel_log_message_n_5	String	Runtime	Log message 5
panel_log_message_n_6	String	Runtime	Log message 4
panel_log_message_n_7	String	Runtime	Log message 3
panel_log_message_n_8	String	Runtime	Log message 2
panel_log_message_n_9	String	Runtime	Log message 1
panel_interface_configuration_message	Switch	Configuration	Interface Configuration Message
panel_zone_status_message	Switch	Configuration	Zone Status Message
panel_zones_snapshot_message	Switch	Configuration	Zones Snapshot Message
panel_partition_status_message	Switch	Configuration	Partition Status Message
panel_partitions_snapshot_message	Switch	Configuration	Partitions Snapshot Message
panel_system_status_message	Switch	Configuration	System Status Message
panel_x10_message_received	Switch	Configuration	X-10 Message Received
panel_log_event_message	Switch	Configuration	Log Event Message
panel_keypad_message_received	Switch	Configuration	Keypad Message Received
panel_interface_configuration_request	Switch	Configuration	Interface Configuration Request
panel_zone_name_request	Switch	Configuration	Zone Name Request
panel_zone_status_request	Switch	Configuration	Zone Status Request
panel_zones_snapshot_request	Switch	Configuration	Zones Snapshot Request
panel_partition_status_request	Switch	Configuration	Partition Status Request
panel_partitions_snapshot_request	Switch	Configuration	Partitions Snapshot Request
panel_system_status_request	Switch	Configuration	System Status Request
panel_send_x10_message	Switch	Configuration	Send X-10 Message
panel_log_event_request	Switch	Configuration	Log Event Request
panel_send_keypad_text_message	Switch	Configuration	Send Keypad Text Message
panel_keypad_terminal_mode_request	Switch	Configuration	Keypad Terminal Mode Request
panel_program_data_request	Switch	Configuration	Program Data Request
panel_program_data_command	Switch	Configuration	Program Data Command
panel_user_information_request_with_pin	Switch	Configuration	User Information Request with PIN
panel_user_information_request_without_pin	Switch	Configuration	User Information Request without PIN
panel_set_user_code_command_with_pin	Switch	Configuration	Set User Code Command with PIN
panel_set_user_code_command_without_pin	Switch	Configuration	Set User Code Command without PIN
panel_set_user_authorization_command_with_pin	Switch	Configuration	Set User Authorization Command with PIN
panel_set_user_authorization_command_without_pin	Switch	Configuration	Set User Authorization Command without PIN
panel_store_communication_event_command	Switch	Configuration	Store Communication Event Command
panel_set_clock_calendar_command	Switch	Configuration	Set Clock / Calendar Command
panel_primary_keypad_function_with_pin	Switch	Configuration	Primary Keypad Function with PIN
panel_primary_keypad_function_without_pin	Switch	Configuration	Primary Keypad Function without PIN
panel_secondary_keypad_function	Switch	Configuration	Secondary Keypad Function
panel_zone_bypass_toggle	Switch	Configuration	Zone Bypass Toggle
partition_bypass_code_required	Switch	Partition Condition	Bypass code required
partition_fire_trouble	Switch	Partition Condition	Fire trouble
partition_fire	Switch	Partition Condition	Fire
partition_pulsing_buzzer	Switch	Partition Condition	Pulsing Buzzer
partition_tlm_fault_memory	Switch	Partition Condition	TLM fault memory
partition_armed	Switch	Partition Condition	Armed
partition_instant	Switch	Partition Condition	Instant
partition_previous_alarm	Switch	Partition Condition	Previous Alarm
partition_siren_on	Switch	Partition Condition	Siren on
partition_steady_siren_on	Switch	Partition Condition	Steady siren on
partition_alarm_memory	Switch	Partition Condition	Alarm memory
partition_tamper	Switch	Partition Condition	Tamper
partition_cancel_command_entered	Switch	Partition Condition	Cancel command entered
partition_code_entered	Switch	Partition Condition	Code entered
partition_cancel_pending	Switch	Partition Condition	Cancel pending
partition_silent_exit_enabled	Switch	Partition Condition	Silent exit enabled
partition_entryguard	Switch	Partition Condition	Entryguard (stay mode)
partition_chime_mode_on	Switch	Partition Condition	Chime mode on
partition_entry	Switch	Partition Condition	Entry
partition_delay_expiration_warning	Switch	Partition Condition	Delay expiration warning
partition_exit1	Switch	Partition Condition	Exit1
partition_exit2	Switch	Partition Condition	Exit2
partition_led_extinguish	Switch	Partition Condition	LED extinguish
partition_cross_timing	Switch	Partition Condition	Cross timing
partition_recent_closing_being_timed	Switch	Partition Condition	Recent closing being timed
partition_exit_error_triggered	Switch	Partition Condition	Exit error triggered
partition_auto_home_inhibited	Switch	Partition Condition	Auto home inhibited
partition_sensor_low_battery	Switch	Partition Condition	Sensor low battery
partition_sensor_lost_supervision	Switch	Partition Condition	Sensor lost supervision
partition_zone_bypassed	Switch	Partition Condition	Zone bypassed
partition_force_arm_triggered_by_auto_arm	Switch	Partition Condition	Force arm triggered by auto arm
partition_ready_to_arm	Switch	Partition Condition	Ready to arm
partition_ready_to_force_arm	Switch	Partition Condition	Ready to force arm
partition_valid_pin_accepted	Switch	Partition Condition	Valid PIN accepted
partition_chime_on	Switch	Partition Condition	Chime on (sounding)
partition_error_beep	Switch	Partition Condition	Error beep (triple beep)
partition_tone_on	Switch	Partition Condition	Tone on (activation tone)
partition_entry1	Switch	Partition Condition	Entry 1
partition_open_period	Switch	Partition Condition	Open period
partition_alarm_sent_using_phone_number_1	Switch	Partition Condition	Alarm sent using phone number 1
partition_alarm_sent_using_phone_number_2	Switch	Partition Condition	Alarm sent using phone number 2
partition_alarm_sent_using_phone_number_3	Switch	Partition Condition	Alarm sent using phone number 3
partition_cancel_report_is_in_the_stack	Switch	Partition Condition	Cancel report is in the stack
partition_keyswitch_armed	Switch	Partition Condition	Keyswitch armed
partition_delay_trip_in_progress	Switch	Partition Condition	Delay Trip in progress (common zone)
partition_secondary_command	Number	Command	Partition Secondary Command
zone_partition2	Switch	Configuration	Partition 2
zone_partition3	Switch	Configuration	Partition 3
zone_partition1	Switch	Configuration	Partition 1
zone_partition4	Switch	Configuration	Partition 4
zone_partition5	Switch	Configuration	Partition 5
zone_partition6	Switch	Configuration	Partition 6
zone_partition7	Switch	Configuration	Partition 7
zone_partition8	Switch	Configuration	Partition 8
zone_name	String	Configuration	Name
zone_fire	Switch	Configuration	Fire
zone_24hour	Switch	Configuration	24 Hour
zone_key_switch	Switch	Configuration	Key-switch
zone_follower	Switch	Configuration	Follower
zone_entry_exit_delay_1	Switch	Configuration	Entry / exit delay 1
zone_entry_exit_delay_2	Switch	Configuration	Entry / exit delay 2
zone_interior	Switch	Configuration	Interior
zone_local_only	Switch	Configuration	Local only
zone_keypad_sounder	Switch	Configuration	Keypad Sounder
zone_yelping_siren	Switch	Configuration	Yelping siren
zone_steady_siren	Switch	Configuration	Steady siren
zone_chime	Switch	Configuration	Chime
zone_bypassable	Switch	Configuration	Bypassable
zone_group_bypassable	Switch	Configuration	Group bypassable
zone_force_armable	Switch	Configuration	Force armable
zone_entry_guard	Switch	Configuration	Entry guard
zone_fast_loop_response	Switch	Configuration	Fast loop response
zone_double_eol_tamper	Switch	Configuration	Double EOL tamper
zone_type_trouble	Switch	Configuration	Trouble
zone_cross_zone	Switch	Configuration	Cross zone
zone_dialer_delay	Switch	Configuration	Dialer delay
zone_swinger_shutdown	Switch	Configuration	Swinger shutdown
zone_restorable	Switch	Configuration	Restorable
zone_listen_in	Switch	Configuration	Listen in
zone_faulted	Contact	Zone Condition	Faulted (or delayed trip)
zone_tampered	Switch	Zone Condition	Tampered
zone_trouble	Switch	Zone Condition	Trouble
zone_bypassed	Switch	Zone Condition	Bypassed
zone_inhibited	Switch	Zone Condition	Inhibited (force armed)
zone_low_battery	Switch	Zone Condition	Low battery
zone_loss_of_supervision	Switch	Zone Condition	Loss of supervision
zone_alarm_memory	Switch	Zone Condition	Alarm memory
zone_bypass_memory	Switch	Zone Condition	Bypass memory

# Full Example

The following is an example of a things file (caddx.things):

Bridge caddx:bridge:thebridge  "Bridge"                   [ protocol="Binary", serialPort="/dev/ttyUSB0", baud=38400, maxZoneNumber=18 ] {
    Thing partition partition1 "Groundfloor alarm"        [ partitionNumber=1 ]
    Thing zone      zone1      "Livingroom motion sensor" [ zoneNumber=1 ]
    Thing zone      zone2      "Bedroom motion sensor"    [ zoneNumber=2 ]
    Thing zone      zone3      "Guestroom motion sensor"  [ zoneNumber=3 ]
    Thing zone      zone4      "Livingroom window"        [ zoneNumber=4 ]
    Thing zone      zone5      "Bedroom window"           [ zoneNumber=5 ]
    Thing zone      zone6      "Guestroom window"         [ zoneNumber=6 ]
}

The following is an example of an items file (caddx.items):

Group:Contact:OR(OPEN,CLOSED)  MotionSensors   "Motion Sensors [%s]"   <motion>
Group:Contact:OR(OPEN,CLOSED)  Windows         "Windows open [%s]"     <window>

Contact   Bedroom_Motion        "Bedroom [%s]"          <motion>       (MotionSensors)  { channel="caddx:zone:thebridge:zone1:zone_faulted" }
Contact   Livingroom_Motion     "Livingroom [%s]"       <motion>       (MotionSensors)  { channel="caddx:zone:thebridge:zone2:zone_faulted" }
Contact   Guestroom_Motion      "Guestroom [%s]"        <motion>       (MotionSensors)  { channel="caddx:zone:thebridge:zone3:zone_faulted" }
Contact   Bedroom_Window        "Bedroom Window [%s]"   <window>       (Windows)        { channel="caddx:zone:thebridge:zone4:zone_faulted" }
Contact   Livingroom_Window     "Livinroom Window [%s]" <window>       (Windows)        { channel="caddx:zone:thebridge:zone5:zone_faulted" }
Contact   Guestroom_Window      "Guestroom Window [%s]" <window>       (Windows)        { channel="caddx:zone:thebridge:zone6:zone_faulted" }

Switch    Partition1_Armed      "Armed [%s]"            <groundfloor>   { channel="caddx:partition:thebridge:partition1:partition_armed" }
Switch    Partition1_EntryGuard "Entry Guard [%s]"      <groundfloor>   { channel="caddx:partition:thebridge:partition1:partition_entryguard" }

The following is an example of a sitemap file (home.sitemap):

sitemap home label="Home" {
    Frame label="Ground floor" {
    Text item=Partition1_Armed
    Text item=Partition1_EntryGuard

    Text item=MotionSensors
        Text label="Motion Sensors (detailed)" {
            Text item=Bedroom_Motion
            Text item=Livingroom_Motion
            Text item=Guestroom_Motion
        }

    Text item=Windows
        Text label="Windows (detailed)" {
            Text item=Bedroom_Window
            Text item=Livingroom_Window
            Text item=Guestroom_Window
        }
    }
}

Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)

← C-Bus CalDAV Command →