This page is part of archived documentation for openHAB 2.5. Go to the current stable version

# Drayton Wiser Binding

This binding integrates the Drayton Wiser Smart Heating System (opens new window). The integration happens through the HeatHub, which acts as an IP gateway to the ZigBee devices (thermostats and TRVs).

# Supported Things

The Drayton Wiser binding supports the following things:

Bridge	Label	Description
`heathub`	HeatHub	The network device in the controller that allows us to interact with the other devices in the system

Thing	Label	Description
`boiler-controller`	Boiler Controller	The HeatHub attached to the boiler. This also acts as the hub device
`room`	Room Name	Virtual groups of Room Thermostats and TRVs that can have temperatures and humidities
`roomstat`	Thermostat	Wireless thermostats which monitor temperature and humidity, and call for heat
`itrv`	iTRV	Wireless TRVs that monitor temperature, alter the radiator valve state and call for heat
`hotwater`	Hot Water	Virtual thing to manage hot water states
`smart-plug`	Smart Plug	Wireless plug sockets which can be remotely switched

# Discovery

The HeatHub can be discovered automatically via mDNS, however the secret cannot be determined automatically. Once the secret has been configured, all other devices can be discovered by triggering device discovery again.

# Thing Configuration

# HeatHub Configuration

Once discovered, the HeatHub secret needs to be configured. There are a few ways to obtain this, assuming you have already configured the system using the Wiser App.

Temporarily install a packet sniffing tool on your mobile device. Every request made includes the secret in the header.
Enable setup mode on the HeatHub. Connect a machine temporarily to the WiserHeat_XXXXX network and browse to http://192.168.8.1/secret to obtain the secret.

The refresh interval defines in seconds, how often the binding will poll the controller for updates.

The awaySetPoint defines the temperature in degrees Celsius that will be sent to the heathub when away mode is activated.

# Channels

# Readonly Channels

# Boiler Controller

Channel	Item Type	Description
`heatingOverride`	Switch	State of the heating override button on the controller
`heatChannel1Demand`	Number:Dimensionless	Current demand level of heating channel 1
`heatChannel1DemandState`	Switch	Is channel 1 calling the boiler for heat
`heatChannel2Demand`	Number:Dimensionless	Current demand level of heating channel 2
`heatChannel2DemandState`	Switch	Is channel 2 calling the boiler for heat
`currentSignalRSSI`	Number	Relative Signal Strength Indicator
`currentWiserSignalStrength`	String	Human readable signal strength
`currentSignalStrength`	Number	Signal strength value that maps to qualityofservice icon

# Hot Water

Channel	Item Type	Description
`hotWaterOverride`	Switch	State of the hot water override button on the controller
`hotWaterDemandState`	Switch	Is hot water calling the boiler for heat
`hotWaterBoosted`	Switch	Is hot water currently being boosted
`hotWaterBoostRemaining`	Number:Time	How long until the boost deactivates in minutes

# Room

Channel	Item Type	Description
`currentTemperature`	Number:Temperature	Currently reported temperature
`currentHumidity`	Number:Dimensionless	Currently reported humidity (if there is a room stat configured in this room
`currentDemand`	Number:Dimensionless	Current heat demand percentage of the room
`heatRequest`	Switch	Is the room actively requesting heat from the controller
`roomBoosted`	Switch	Is the room currently being boosted
`roomBoostRemaining`	Number:Time	How long until the boost deactivates in minutes
`windowState`	Contact	Is the window open or closed?

# Room Stat

Channel	Item Type	Description
`currentTemperature`	Number:Temperature	Currently reported temperature
`currentHumidity`	Number:Dimensionless	Currently reported humidity
`currentSetPoint`	Number:Temperature	Currently reported set point
`currentBatteryVoltage`	Number:ElectricPotential	Currently reported battery voltage
`currentWiserBatteryLevel`	String	Human readable battery level
`currentBatteryLevel`	Number	Battery level in percent
`currentSignalRSSI`	Number	Relative Signal Strength Indicator
`currentSignalLQI`	Number	Link Quality Indicator
`currentWiserSignalStrength`	String	Human readable signal strength
`currentSignalStrength`	Number	Signal strength value that maps to qualityofservice icon
`zigbeeConnected`	Switch	Is the roomstat joined to network

# Smart TRV

Channel	Item Type	Description
`currentTemperature`	Number:Temperature	Currently reported temperature
`currentDemand`	Number:Dimensionless	Current heat demand percentage of the TRV
`currentSetPoint`	Number:Temperature	Currently reported set point
`currentBatteryVoltage`	Number:ElectricPotential	Currently reported battery voltage
`currentWiserBatteryLevel`	String	Human readable battery level
`currentBatteryLevel`	Number	Battery level in percent
`currentSignalRSSI`	Number	Relative Signal Strength Indicator
`currentSignalLQI`	Number	Link Quality Indicator
`currentWiserSignalStrength`	String	Human readable signal strength
`currentSignalStrength`	Number	Signal strength value that maps to qualityofservice icon
`zigbeeConnected`	Switch	Is the TRV joined to network

# Smart Plug

Channel	Item Type	Description
`currentSignalRSSI`	Number	Relative Signal Strength Indicator
`currentSignalLQI`	Number	Link Quality Indicator
`zigbeeConnected`	Switch	Is the TRV joined to network

# Command Channels

# Boiler Controller

Channel	Item Type	Description
`awayModeState`	Switch	Has away mode been enabled
`ecoModeState`	Switch	Has eco mode been enabled

# Hot Water

Channel	Item Type	Description
`manualModeState`	Switch	Has manual mode been enabled
`hotWaterSetPoint`	Switch	The current hot water setpoint (on or off)
`hotWaterBoostDuration`	Number	Period in hours to boost the hot water

# Room

Channel	Item Type	Description
`currentSetPoint`	Number:Temperature	The current set point temperature for the room
`manualModeState`	Switch	Has manual mode been enabled
`roomBoostDuration`	Number	Period in hours to boost the room temperature
`windowStateDetection`	Switch	Detect whether windows are open

# Room Stat

Channel	Item Type	Description
`deviceLocked`	Switch	Is the roomstat interface locked

# Smart TRV

Channel	Item Type	Description
`deviceLocked`	Switch	Are the TRV controls locked

# Smart Plug

Channel	Item Type	Description
`plugOutputState`	Switch	The current on/off state of the smart plug
`plugAwayAction`	Switch	Should the plug switch off when in away mode
`manualModeState`	Switch	Has manual mode been enabled
`deviceLocked`	Switch	Are the Smart Plug controls locked

# Known string responses for specific channels:

Channel	Known responses
`currentWiserSignalStrength`	`{ "VeryGood", "Good", "Medium", "Poor", "NoSignal" }`
`currentWiserBatteryLevel`	`{ "Full", "Normal", "TwoThirds", "OneThird", "Low", "Critical" }`

# Full Example

# .things file

Bridge draytonwiser:heathub:HeatHub [ networkAddress="192.168.1.X", refresh=60, secret="secret from hub", awaySetPoint=10 ] {
    boiler-controller controller     "Controller"
    room              livingroom     "Living Room"            [ name="Living Room" ]
    room              bathroom       "Bathroom"               [ name="Bathroom" ]
    room              bedroom        "Bedroom"                [ name="Bedroom" ]
    roomstat          livingroomstat "Living Room Thermostat" [ serialNumber="ABCDEF1234" ]
    itrv              livingroomtrv  "Living Room - TRV"      [ serialNumber="ABCDEF1235" ]
    hotwater          hotwater       "Hot Water"
    smart-plug        tvplug         "TV"                     [ serialNumber="ABCDEF1236" ]
}

The name corresponds to the room name configured in the Wiser App. It is not case sensitive. The serialNumber corresponds to the device serial number which can be found on a sticker inside the battery compartment of the Smart Valves/TRVs, and behind the wall mount of the Room Thermostats.

# .items file

Switch Heating_Override      "Heating Override"    <fire>   (gHouse)    { channel="draytonwiser:boiler-controller:HeatHub:controller:heatingOverride" }
Number Heating_Demand      "Heating Demand [%.0f %%]"    <heating>   (gHouse)    { channel="draytonwiser:boiler-controller:HeatHub:controller:heatChannel1Demand" }
Switch Heating_Requesting_Heat      "Heating On"    <fire>   (gHouse)    { channel="draytonwiser:boiler-controller:HeatHub:controller:heatChannel1DemandState" }
Switch Heating_Away_Mode      "Away Mode"    <vacation>   (gHouse)    { channel="draytonwiser:boiler-controller:HeatHub:controller:awayModeState" }
Switch Heating_Eco_Mode      "Eco Mode"    <climate>   (gHouse)    { channel="draytonwiser:boiler-controller:HeatHub:controller:ecoModeState" }

/* Heating */
Switch Heating_GF_Living      "Heating"    <fire>   (GF_Living, Heating)    ["Heat Request"] { channel="draytonwiser:room:HeatHub:livingroom:heatRequest" }

/* Indoor Temperatures */
Number:Temperature livingroom_temperature    "Temperature [%.1f °C]" <temperature> (GF_Living, Temperature)    ["Temperature"] {channel="draytonwiser:room:HeatHub:livingroom:currentTemperature"}

/* Setpoint Temperatures */
Number:Temperature livingroom_setpoint    "Set Point [%.1f °C]" <temperature> (GF_Living)    ["Set Point"] {channel="draytonwiser:room:HeatHub:livingroom:currentSetPoint"}

/* Heat Demand */
Number livingroom_heatdemand    "Heat Demand [%.0f %%]" <heating> (GF_Living)    ["Heat Demand"] {channel="draytonwiser:room:HeatHub:livingroom:currentDemand"}

/* Manual Mode */
Switch ManualMode_GF_Living      "Manual Mode"    <switch>   (GF_Living)    ["Manual Mode"] { channel="draytonwiser:room:HeatHub:livingroom:manualModeState" }

/* Boost Mode */
Switch BoostMode_GF_Living      "Boosted"    <fire>   (GF_Living)    ["Boost Mode"] { channel="draytonwiser:room:HeatHub:livingroom:roomBoosted" }

/* Boost Duration */
Number BoostDuration_GF_Living      "Boost For[]"    <text>   (GF_Living)    ["Boost Duration"] { channel="draytonwiser:room:HeatHub:livingroom:roomBoostDuration" }

/* Boost Remaining */
Number BoostRemaining_GF_Living      "Boost Remaining"    <text>   (GF_Living)    ["Boost Remaining"] { channel="draytonwiser:room:HeatHub:livingroom:roomBoostRemaining" }

/* Humidity */
Number:Humidity livingroom_humidity  "Humidity [%.0f %%]" <humidity> (GF_Living) ["Humidity"] {channel="draytonwiser:room:HeatHub:livingroom:currentHumidity"}

# Sitemap

Text label="Living Room" icon="sofa" {
    Text item=livingroom_temperature
    Setpoint item=livingroom_setpoint step=0.5
    Text item=livingroom_humidity
    Text item=Heating_GF_Living
    Text item=livingroom_heatdemand
    Switch item=ManualMode_GF_Living
    Text item=BoostMode_GF_Living
    Switch item=BoostDuration_GF_Living icon="time" mappings=[0="0", 0.5="0.5", 1="1", 2="2", 3="3"]
    Text item=BoostRemaining_GF_Living icon="time"
}

Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)

← Doorbird Dresden Elektronik deCONZ →